![]() ![]() Auto-setup requires enabling the Autodiscovery feature of Microsoft Exchange Server. Requires Microsoft Exchange Server 2007 Service Pack 1 Update Rollup 4, Exchange Server 2010, or Exchange 2013. New Boot Camp installations require Windows 8 or Windows 10 (sold separately). Supports existing Boot Camp installations with Windows XP Service Pack 2, Windows Vista, Windows 7, Windows 8, or Windows 10. Video calls require a built-in FaceTime camera, an iSight camera (built in or external), a USB video class (UVC) camera, or a FireWire DV camcorder and broadband Internet connection. Requires a FaceTime or iSight camera (built in or external), USB video class (UVC) camera, or FireWire DV camcorder. Requires an additional hard drive or AirPort Time Capsule (sold separately). Mac Pro (Early 2009 with AirPort Extreme card, or Mid 2010 or newer).SMS requires an iPhone with iOS 8.1 or later and an activated carrier plan.ĪirDrop between Mac computers and iOS devices is supported by the following Mac models:ĪirDrop to iOS devices requires an iPhone, iPad, or iPod touch with a Lightning connector and iOS 7 or later.ĪirDrop between two Mac computers is supported by the following Mac models: Phone calling requires an iPhone with iOS 8 or later and an activated carrier plan. Requires Personal Hotspot service through your carrier. Instant Hotspot requires an iPhone or iPad with cellular connectivity with a Lightning connector and iOS 8.1 or later. Handoff requires an iPhone, iPad, or iPod touch with a Lightning connector and iOS 8 or later. MacBook (Late 2008 Aluminum, or Early 2009 or newer).These Mac models are compatible with OS X El Capitan: Some features require a compatible Internet service provider fees may apply.įor details about your Mac model, click the Apple icon at the top left of your screen, choose About This Mac, then choose More Info.Some features require an Apple ID terms apply.To avoid packet loss, the baud rate should be higher than 250kbps, which is the maximum bitrate of the 802.15.4 2. Q1: high packet loss rate when sniffing heavy trafficĪ1: use higher uart baud rate in Sniffer firmware(NCP), and use '-b ' option to set the same baud rate on host side. This will connect to stock openthread ncp firmware over the given UART, make the node into a promiscuous mode sniffer on the given channel, open up wireshark, and start streaming packets into wireshark. sniffer.py -c 11 -tap -u /dev/ttyUSB0 | wireshark -k -i. To display Channel on Wireshark: (only for Wireshark 3.0 and later) sniffer.py -c 11 -n 1 -rssi -u /dev/ttyUSB0 | wireshark -k -i. sniffer.py -c 11 -n 1 -no-reset -u /dev/ttyUSB0 | wireshark -k -i -Įdit->Preferences->Protocols->IEEE802.15.4, enable "TI CC24xx FCS format" optionĮdit->Preferences->Appearance->Columns, add a new entry: sniffer.py -c 11 -n 1 -crc -u /dev/ttyUSB0 | wireshark -k -i -įor the sniffers that are connected to the host with the native USB connection and reset during init results in failed start: sniffer.py -c 11 -n 1 -u /dev/ttyUSB0 | wireshark -k -i -įor the sniffers that do not provide the crc: If not specified, DLT_IEEE802_15_4_WITHFCS(195) would be used by default with the additional RSSI, LQI following the PHY frame directly (TI style FCS format).įor building an OpenThread ncp to support sniffer:Īdd -enable-raw-link-api as a build option Specify DLT_IEEE802_15_4_TAP(283) for frame format, with a pseudo-header containing TLVs with metadata (e.g. Recalculate crc for NCP sniffer (useful for platforms that do not provide the crc).ĭo not reset the NCP during initialization (useful for some NCPs with the native USB connection). Output packets as ASCII HEX rather than pcap. Required to stream to Wireshark.ġ: Show spinel property changes and values.ģ: Show spinel raw packet bytes (after HDLC decoding).ĥ: Show spinel raw stream bytes: all serial traffic to NCP. Enabling debug output is typically coupled with -x.Ġ: Supress all debug output. The unique nodeid for the HOST and NCP instance. Note: will eventually map to hostname:port tuple. This is useful for SPI configurations when used in conjunction Open a socket connection to the OpenThread NCP device Spinel-cli will communicate with the child process Where is the command to start an emulator, such as ![]() Open a piped process connection to the OpenThread NCP device Set the uart baud rate, default is 115200.Įnable the serial connection hardware flow control. Where is a device path such as "/dev/ttyUSB0". Open a serial connection to the OpenThread NCP device
0 Comments
Leave a Reply. |